CYCLOPS PARALYSER 755 Manuel d'instructions
Naviguer en ligne ou télécharger Manuel d'instructions pour Alarme de voiture CYCLOPS PARALYSER 755. CYCLOPS PARALYSER 755 Instruction manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PARALYSER 755
USER INSTRUCTIONS
Proudly designed and engineered
in Australia by Dynamco Pty Ltd.
Congratulations on having one of the world's most
advanced and unique Australian designed and
engineered vehicle security systems, installed in your
vehicle!
The Cyclops Paralyser 755 complies with
Australian Standards AS/NZS 4601:1999.
Ensure your warranty details are completed at time of installation / purchase, refer to back cover
of this instruction manual.
ARMING AND DISARMING
To arm or disarm the system, press the main button on the remote control. The
vehicle indicators will confirm any remote operation. Two flashes for arm and one
flash for disarm. The blue status LED on the dash will flash when the immobiliser
is armed. The P755 is also fitted with a transponder style disarm feature. Mounted
behind the dash is a electronic transponder
pickup antenna. The antenna scans any
remote that is placed within range. Any valid
remote control will disarm the immobiliser
automatically when the engine is turned on.
AUDIBLE CONFIRMATION
(optional - requires horn connection)
PANIC (optional - requires horn connection)
If the main button on the remote control is pressed and held down for more than
two seconds the system will go into a panic mode. In this mode the indicators will
flash and the horn/siren will pulse. The panic mode will continue for thirty
seconds. If you wish to cancel the panic signal before the thirty seconds then
simply press the main button of the remote control again.
BOOT RELEASE (optional - requires boot solenoid connection)
Press the second button on the remote control and keep it depressed until the boot
releases. This will take about 3 seconds. A successful boot release signal will flash
the vehicle indicators four times. This function can only operate if the vehicle is
equipped with an electrical boot release.
The P755 has optional circuitry that is used to
sound a siren or vehicle horn. The horn/siren
can be made to sound each time the P755 is
armed or disarmed. The siren can also sound a warning if the vehicle is broken
into. The P775 will also alert the user to open doors or bonnet, by chirping the siren
rapidly while arming.
TEMPORARY SILENT ARMING
To cancel the audible arm or disarm chirp for one operation, press the second
button momentarily before pressing the main button. The confirmation chirps will
be re-enabled for the next operation.
AUTO-ARMING
The P755 is designed to automatically immobilise the vehicle. The engine will be
immobilised within 40 seconds after the ignition has been turned off. If disarmed
by remote control, the P755 will re-arm (immobiliser only) itself within the same
time period.
AUTO-RELOCK & RE-ARM
(optional - requires central locking connection)
If the P755 is disarmed and no doors are opened, it will rearm
within 40 seconds. If central locking is fitted and connected to the
P755, the immobiliser will also re-lock the doors and re-arm the
alarm 120 seconds later. The P755 will not lock the doors if any
have been opened during this time. This feature is provided to re-
secure the vehicle incase of an accidental disarm.
ANTI HIJACK (optional - requires central locking
connection)
One second after the ignition is switch to the ON position, the P755 will lock the
cars doors. The lock signal will be cancelled if the P755 receives an open door
signal from the car. When the ignition switch is turned off, the P755 will unlock
the doors. This feature comes as standard, and can be disabled (see Selectable
Options).
ENGINE IMMOBILISATION
When the system is armed the engine is immobilised. The
two independent, normally open circuits of
immobilisation ensures that two key sections of the
engine are deprived of power. Immobilisation points vary
from vehicle to vehicle; common places include fuel
injection, fuel pump, fuel cut-off solenoids, main ignition
CYCL PS
R
U
I
C
T
Y
E
S
S
S
Y
S
M
T
E
feed, low-tension distributor supplies and starter motor solenoids, etc.
INTRUSION DETECTION
(optional - requires horn connection)
When the P755 has been armed by the remote control and a door is opened the
vehicle indicators will flash immediately. The horn will sound in conjunction with
the flashing of the indicators. Once the P755 has been triggered, the trigger cycle
will flash and sound for 30 seconds or until disarmed by the remote control. If after
30 seconds the door is still open, the indicators will cease flashing and the horn
stops pulsing, wait five seconds and trigger again. If the door is still open, the
alarm function will cycle once more and then ignore further triggers. Any
additional sensors added to the P755 are regarded as separate inputs, and will also
trigger a maximum of three times.
If the P775 has auto armed (immobilised), the doors will not trigger the siren. The
engine will remain immobilised all the time.
For the first five seconds after arming, the P775 alarm is inactive. This allows
electric antennas to retract and dome lights to extinguish before the alarm
becomes active. If any circuit has triggered before the five seconds elapses, the
countdown will reset until the circuit becomes idle.
SELECTABLE OPTIONS
The PARALYSER 755 has a number of options than can be set or reset by means
of the ignition switch and remote control. To change these options you need to do
the following:
! Disarm the P755, open the driver’s door, and
leave door open.
! Turn the ignition switch from ACC to the ON
position the required number of times. Each turn of
the key should take no longer than one second.
Count each time the switch is in the ON position.
! Leave the switch in the ON position when the
required number is reached.
! The vehicle indicators will flash approximately
two seconds after last turn, indicating the P755 is ready to alter option setting.
! Immediately press the main button on either valid remote control.
! The P755 will respond by flashing the indicators. Three flashes shows that the
option is set and one flash shows it has been reset. See below for option numbers
and descriptions.
The following list details how many times you need to turn the ignition on to
achieve the desired change.
IGNITION SWITCH TURNS 1 FLASH 3FLASHES
3 ANTI HIJACK DISABLED ENABLED
7 PROGRAM’ NEW REMOTE PRESS REMOTE --------------
9 DOME LIGHT UPON DISARM DISABLE ENABLED
11 HORN/SIREN OUTPUT TYPE PULSED CONSTANT
13 ARM/DISARM CONFIRMATION DISABLED ENABLED
15 120 SEC RELOCK DISABLED ENABLED
17 C/LOCKING PULSE TIME*** 0.8 SEC 3 SECS
19 CHANGE PIN CODE (2 FLASHES) BEGIN NEW PIN
21 OPEN DOOR WARNING DISABLED ENABLED
*** do not change - installer only (incorrect setting will damage central locking)
OVERRIDE
The system can be overridden by means of a Personal Identification Number
(PIN). Every unit is supplied with its
own PIN. It is important to make a note of this PIN or keep the card supplied with
the unit in a safe p1ace as it also has the PIN detailed on it.
** Any digit marked '0', indicates 10 flashes.
OVERRIDE PROCEDURE
! Insert the ignition key into the ignition
switch and turn to the ON position.
The blue status LED mounted on the
dash will glow constantly.
! Turn the ignition key back to the ACC
position, the status LED will begin to
flash slowly. Count the number of
flashes for the first digit in the PIN of
the P755. Return the key to the ON
position when the correct number is
counted.
! Repeat step 2 for the remaining digits in the PIN. When all four digits are
entered, the indicators will flash once, the P755 will then disarm.
NB: If the engine is not started within 40 seconds of over-riding, the P755 will
immobilise the engine.
BATTERY REPLACEMENT
Using a small Phillips-head screwdriver, remove the three screws at the back of the
remote and carefully separate the two
body housings taking take care not to
disturb the circuit board. Remove the
old battery whilst paying attention to
the orientation of the positive and
negative terminals.
Insert new battery in identical fashion
to the original and re-assemble
remote. Replace screws and test
remote control by pressing main
button. For further information,
please contact your local Cyclops service centre.Remote battery type 27a.
It is necessary to enter pin override each time the engine
is turned off and the P755 has auto immobilised
1
2
Résumé du contenu
Page 1 - PARALYSER 755
PARALYSER 755 USER INSTRUCTIONSProudly designed and engineered in Australia by Dynamco Pty Ltd.Congratulations on having one of the world's
Page 2 - WARRANTY REGISTRATION
CHANGING PIN CODE!To alter the PIN code of the system, follow the standard option change procedure; select option #19. !The vehicle indicators will fl
Plus de documents pour Alarme de voiture CYCLOPS PARALYSER 755
CYCLOPS PARALYSER 755 Manuel d'utilisateur
(285 pages)
CYCLOPS PARALYSER 755 Spécifications
(20 pages)
© 2020, manymanuals.fr. Tous droits réservés | 6.330 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels